Get to know your Rogue vinyl cutter better. View these training videos in order or use the playlist to navigate to the video most relevant to your immediate needs for basic or advanced cutting instructions.


BASIC

1. Unboxing

  • Crossbar :07
  • Media bar :10
    • Pro come with 2
  • Accessory Box :15
    • Power cable :18
    • USB communication cable :19
    • Blades :21
    • Pen :24
    • Hardware :26
  • Unwrap cutter :29
  • Stand leg parts :40

2. Stand Assembly

  • Assemble foot 1:00
  • Attach foot to leg 1:15
  • Add crossbar 1:44
  • Add media holder 2:21
  • Place cutter on stand 2:41
  • Add media basket 2:51
    • Exclusively with Rogue Pro

3. Install Driver

  • Install power cable  :06
  • Power On :07
  • Menu to VirtualCom N, Printer Y :11
  • Download driver from tech site :27
  • Extract Zipped folder :38
  • Click Setup  :45
  • Connect USB Cable :57

4. LXi Software

  • Create SAi account :03
  • Download software 1:27
  • Begin Installation 2:02
  • Activate software license 2:45
  • Add cutter setup to software 3:21

5. Loading Vinyl/Control Panel

  • Pinch Rollers :04
  • Media Bar :18
  • Speed/Force :41
  • Language 1:09
  • X/Y Scale 1:14
  • Operation Mode 1:22
  • UD File 1:31
  • Laser 1:36
  • Reset 1:50
  • Online 2:00
  • Origin Point 2:20
  • Pause/Test Cut 2:45

6. Blade Depth 

  • Bad cut :04
  • Power off :17
  • Examine blade :20
  • Adjust blade depth :33
  • Return blade holder to carriage :45

7. First Cut

  • Design :13
  • Import file :24
  • Cut/plot :39
  • Default job properties :58
  • Change orientation 1:37
  • Send 1:51

ADVANCED


8. Cut from Thumb Drive (UD)

  • Export design to thumb drive :09
  • Menu to “UD file” setting :33
  • Insert thumb drive :41
  • Press enter :54

9. Contour Cut with LXi Master Plus

  • Add contour cut effect :24
  • Add copies :49
  • Add registration marks 1:09
  • Send to printer 1:35
  • Load printed media onto cutter 2:00
  • Set origin point 2:18
  • Set laser 2:26
  • Cut contour 2:43
  • Send to cutter 3:02

10. Contour Cut with Rip and Print

  • Add contour cut effect :17
  • Rip & print :26
  • Contour cut settings :41
  • Send to printer 1:54
  • Load printed media onto cutter 2:14
  • Set origin point 2:33
  • Set laser 2:43
  • Send to cutter 2:59

11. Segmented Registration Marks

  • Select design :17
  • Click rip/print :19
  • Increase number of copies :27
  • Contour cut settings :30
  • Send to printer 1:12
  • Load printed media onto cutter 1:22
  • Set origin point 1:33
  • Menu to laser 1:36
  • Enter to scan mark  1:33
  • Enter to accept 1:48
  • Send to cutter 2:03

12. Adjust CC Offset

  • Download and print test page :11
  • Set origin point inside registration mark :22
  • Menu to laser :30
  • Press enter :36
  • Measure distance between line and cross mark :46
  • Enter laser setup 1:09
  • Adjust setting based on formula  1:32
  • Press enter 1:52
  • Retest alignment 1:58

13. CC Physical Adjust

  • Remove 2 screws holding securing carriage casing :28
  • Remove casing (lift and tilt forward) :43
  • Loosen 2 screws in front that secure the laser :48
  • Adjust the laser to 4 1/5 mm (3 stacked pennies) from media :57
  • Tighten screw 1:06
  • Run test 1:15
  • If laser scans mark, return casing and screws (not shown)

14. CC Scale Adjust

Note: Perform the CC Offset Adjustment before adjusting the scale.

  • Menu to X/Y Scale Adjustment :28
  • Press the up arrow :32
  • enter the password (12), and press enter :32
  • Adjust the needed axis (X, Y or both) in small increments and then larger if needed. :42
  • Press enter (the bombsite button) 1:03
  • Menu to Laser and press enter for test scan 1:07
  • Send job to scan 1:19

ADDITIONAL RESOURCES